Roof Coating Contractor for Industrial and Federal Facilities
Goggans Coatings installs roof coating systems for warehouses, motor pools, maintenance facilities, and commercial buildings across Alabama and the Southeast. A roof coating restores and protects an aging roof that's still structurally sound, without the cost and downtime of a full tear-off and replacement.
If you're a facilities manager, general contractor, or property owner with a roof that's past its prime but not ready for a full replacement, this is what we bring to the job.
Where Roof Coating Gets Used
Roof coating is a fluid-applied system installed over an existing roof, metal panel, single-ply membrane, modified bitumen, or built-up roofing to seal it, stop active leaks, and extend service life. It's the right call for a roof that's aging but sound: rusting metal panels, chalking membranes, or seams that have started to fail.
Applied correctly, a roof coating system can extend the service life of a roof that would otherwise be due for replacement by 10 to 20 years. Applied over a roof that hasn't been properly assessed, a coating fails within a season, usually at the same seams and penetrations that were already failing before the coating went down.
Federal and Military Roof Work
Roof coating is part of our broader painting and coatings scope on federal and military installations, alongside our interior/exterior painting and epoxy flooring work on those sites. Federal roof work carries the same requirements as our other federal contracts: certified payroll, EM 385-compliant safety plans, and coordination with base access and scheduling. We're already set up for that. Our crews carry the same compliance credentials on a roof job that we carry on a painting or flooring contract, so there's no separate vetting process if you've already worked with us.
Roof Assessment and Prep: The Part That Determines Whether the Coating Lasts
A roof coating fails for the same reason an epoxy floor does: the substrate wasn't properly assessed and prepped before the coating was applied. We don't skip this step.
Our process includes:
Roof inspection and moisture survey to identify wet insulation, active leaks, and any areas a coating can't reach. A coating buys years on a sound roof. It doesn't fix a roof that's already saturated underneath.
Substrate cleaning and rust or contaminant removal, so the coating bonds to the roof instead of to dirt, chalking, or corrosion sitting on top of it
Seam, flashing, and penetration repair before any coating goes down, since these are the first places a roof fails regardless of what's applied over them
Ponding water assessment to determine whether the roof needs slope correction, added drainage, or a coating system rated for standing water
A coating applied over a roof that skipped this step fails in the same spots where the old roof was already failing. This is where we spend the time that other contractors try to save.
Roof Coating Systems We Install
Not every roof needs the same system. We install:
Silicone roof coatings for roofs with ponding water or high UV exposure. Silicone stays flexible and resists breakdown in standing water, where acrylic softens over time.
Acrylic elastomeric coatings for well-drained roofs where reflectivity and lower cost matter, common on large warehouse and commercial roofs.
Polyurethane roof coatings for roofs with foot traffic or equipment loading, since polyurethane resists abrasion better than acrylic or silicone alone.
Metal roof restoration systems for rusting or chalking metal panel roofs, common on motor pools, hangars, and industrial buildings, to encapsulate existing rust and seal seams and fasteners.
We spec the system to the roof and its exposure, not the other way around. A ponding low-slope membrane and a rusting metal warehouse roof don't need the same coating.
Certifications & Compliance
Facility managers and contracting officers can verify the following before award:
Active SAM.gov registration / verified CAGE code
NAICS 238320 — Painting and Wall Covering Contractors
OSHA 30-Hour Construction certification
EM 385-1-1 safety plan compliance
Davis-Bacon Act compliance & certified payroll submission
RRP (Renovation, Repair and Painting) certification for lead paint
Alabama contractor's license
Work With Us
We keep a small team, which means the people you talk to are the people doing the work. Shane Goggans runs every job personally, roof jobs included. If you're bidding a warehouse, motor pool, or maintenance facility roof and need a contractor who understands industrial and federal requirements, reach out directly.
Follow us on LinkedIn · Follow Us On LinkedIn · Follow us on LinkedIn ·
Follow us on LinkedIn · Follow Us On LinkedIn · Follow us on LinkedIn ·
Frequently Asked Questions
-
Most systems carry 10 to 20 year warranties over a properly prepped roof, with silicone systems sometimes running longer. Coating life depends more on prep and roof condition going in than on the product itself.
-
Silicone holds up best on roofs with standing water and high UV exposure. Acrylic costs less and performs well on well-drained roofs. Polyurethane handles foot and equipment traffic better than either. We spec the system to the roof.
-
Sometimes, if the leak is coming from a seam, flashing, or fastener issue we can repair before coating. A roof with saturated insulation or structural damage needs more than a coating, and we'll tell you that up front rather than coat over a bigger problem.
-
Yes. Metal roof restoration, rust encapsulation, and seam and fastener sealing on metal panel roofs is part of the same scope as membrane and built-up roof coating.
-
Generally, yes, since a coating extends the life of the existing roof deck and membrane rather than tearing them off. It's not the right call for every roof, and we'll assess the roof and tell you plainly whether coating or replacement makes sense.
-
Yes. Roof coating work can be scheduled and sequenced so operations underneath continue without interruption.